When you logged into the system locally the network interface appeared to be up but you could not connect to anything outside of the VM. If I rebooted the VM it would work for a few hours or less and then the network would drop out again. Digging through the event viewer I came across these:
RFC 4214 ISATAP October 2005 querying the DNS service, querying a site-specific name service, or with an unspecified alternate method. After initializing an ISATAP interface's PRL, the node sets a timer for the interface to PrlRefreshInterval seconds and re-initializes the interface's PRL as specified above when the timer expires. ISATAP functionality is enabled by creating a tunnel of mode isatap using the ip tunnel command. A specific IPv4 address must be chosen as the ISATAP router address, and this address generally must not be used to any other IP tunnels. If V4ADDR is the chosen address, the command syntax to create a new ISATAP interface on the router would be: The ISATAP interface is made up of “0000:5efe” followed by the 32 bits IPv4 address of the ISATAP interface. The part before the IPv4 address could also be “0200:5efe” if the IPv4 address is a public IPv4 address. Apr 20, 2014 · Address: ISATAP interfaces automatically configure themselves with an IPv6 address. The 64 bit network prefix could be a link-local, unique local, or global prefix. The 64 bit interface address is the IPv4 address (32 bits) prefixed with 0000:5EFE (for a private IPv4 address) or 0200:5E5E (for a public IPv4 address) (32 bits). The IPv4 address Sep 07, 2018 · Symptom Event 4201: isatap interface is no longer active. Event 1135: cluster node was removed from the active failover cluster membership. . Resolution Edit Registry Location: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\services\TCPIP6\Parameters KeyType: DWORD (32-bit) KeyName: DisabledComponents KeyValue: FF Reference Link Modify Failover Cluster Parameters Import-module failoverclusters RFC 5214 ISATAP March 2008 7.3.Decapsulation The specification in Section 3.6 of [RFC4213] is used. Additionally, when an ISATAP node receives an IPv4 protocol 41 datagram that does not belong to a configured tunnel interface, it determines whether the packet's IPv4 destination address and arrival interface match a locator configured in an ISATAP interface's locator set.
Aug 11, 2012 · MICROSOFT ISATAP x422 and MICROSOFT TEREDO TUNNELING ADAPTER I have a problem regarding my MICROSOFT ISATAP x422 and MICROSOFT TEREDO TUNNELING ADAPTER. going to device manager there is a yellow mark on MICROSOFT ISATAP x422 and MICROSOFT TEREDO TUNNELING ADAPTER icon and i was wondering what was wrong. Please help me. Hardware & Devices
On a Windows Server 2008-based computer, a Domain Name System (DNS) server does not listen on the ISATAP interface. Additionally, if you right-click the server in DNS Manager (Dnsmgmt.msc) and then click Properties on the Interface tab, the ISATAP address is not listed. 转 ipv6 isatap隧道配置-keep running -51CTO博客 2011-11-2 · ISATAP隧道用于IPv4域内的IPv6主机与IPv6域进行通讯，总结基本配置如下： 配置拓扑图 1>. PC机的相关命令序列 c:\>Ipv6 install //在PC上安装Ipv6 c:\> netsh interface ipv6 isatap set router 10.1.2.1 //在PC上指定要接入ISATAP路由器 c
Apr 20, 2014 · Address: ISATAP interfaces automatically configure themselves with an IPv6 address. The 64 bit network prefix could be a link-local, unique local, or global prefix. The 64 bit interface address is the IPv4 address (32 bits) prefixed with 0000:5EFE (for a private IPv4 address) or 0200:5E5E (for a public IPv4 address) (32 bits). The IPv4 address
2020-3-18 · C:\> netsh interface ipv6 isatap set router 10.1.1.1 C:\> netsh netsh> interface netsh interface> ipv6 netsh interface ipv6>isatap netsh interface ipv6 isatap>set router 10.1.1.1 enabled 1440 配置Switch_2 # 配置接口的IPv6地址。 上海交通大学校园网支持ipv6吗？ - 知乎 2018-1-7 · netsh interface ipv6 isatap set router isatap. sjtu. edu. cn netsh interface ipv6 isatap set state enabled 即可启用校内isatap隧道服务器。 该服务器仅校园网内可以访问，校外无法使用，小路由器后的用户（如用户IP为192.168.x.x，但不限于该IP前缀，请咨询本地IT）无法使用。